상품명 | Flyduino KISS 24A 변속기(2-5S, race edition, V1.08) |
---|---|
판매가 | 25,000원 |
국내·해외배송 | 국내배송 |
배송방법 | 택배 |
배송비 | 3,500원 (500,000원 이상 구매 시 무료) |
SNS 상품홍보 | |
---|
(최소주문수량 1개 이상 / 최대주문수량 0개 이하)
사이즈 가이드수량을 선택해주세요.
위 옵션선택 박스를 선택하시면 아래에 상품이 추가됩니다.
상품명 | 상품수 | 가격 |
---|---|---|
Flyduino KISS 24A 변속기(2-5S, race edition, V1.08) | 25000 () |
할인가가 적용된 최종 결제예정금액은 주문 시 확인할 수 있습니다.
(점심 12시 30분 - 1시 30분)
토/일요일 및 공휴일은 휴무입니다.
배송/재고 문의 : 070-7715-2210
상품/기술 문의 : 070-7715-2211
"평일 5시 전으로 주문하시면 당일 발송됩니다."
Flyduino KISS 24A esc race edition V1.08
- 독일 Flyduino사의 전자변속기입니다.
- KISS FC와 사용하시면 됩니다.
- 연속 24A, 최대 30A의 출력을 가졌습니다.
V1.03과 V1.08은 펌웨어 차이입니다. V1.08은 최신펌웨어가 올라가 있습니다.
구성
KISS 변속기 1개
Features
32-bit ARM Cortex MCU @48Mhz
Telemetry capability (voltage, current, temp, rpm)
Over-current protection (measures the current and reduces it to max 30A)
Over temperature protection (reduces the max power if hotter then 120°C)
Expanded adaptive auto timing (3,25-30° advance will be calculated on each commutation)
For Race Multicopters (24A continuous also with bad cooling *)
High max. RPM (450.000ERpm, 64.000Rpm with a 14Pol Motor)
Small size (19 x 27 mm)
Accurate RPM control (~ 950 steps)
No additional capacitor needed**
Very fast throttle response
Linear throttle response
Active freewheeling (low diode losses)
Regenerative braking
Fast FET switching because of the use of gate drivers
2-5S LiPo**
Oneshot42, Oneshot125 and normal (25 ? 500Hz) PWM auto detected.
DMA hardware support - Direct Memory Access - keeps the cpu load low while using Dshot 600
100% compatible hardware for digital protocolls - Dshot
Operating voltage 6 - 25V
Maximum continuous current 24A
Instantaneous maximum current 30A active limited
500,000 ERPM maximum field speed (use of 450,000 recommended)
(**) For very long LiPo power lines (more than 20cm) or for smoothing the power supply, attache a 100 - 400µF Low ESR 25V (or more) electrolytic capacitor to the power pads. Caution! When used with 5S lipo, the use of a electrolytic capacitor is recommended. (*) e.g. When mounted between two CF plates
Safety Warnings
Due to the regenerative braking, the KISS ESC should only be powered by LiPo batteries.
Never start a brush-less motor in your hands!
While starting up with propellers mounted, always care for distance yourself and objects
Never power up your ESC/speed controllers without a valid signal transmitter (receiver or FC) is connected.
The KISS ESC can be locally heated up to 80 ° C during operation!
While soldering do not connect a voltage source at the ESC / speed controller.
Some components on the KISS ESC can be destroyed by static charge. When handling such electronics, make sure to be grounded
Read the Wiki section for Electrostatic Discharge before soldering.
DOWNLOADS (Manuals, Firmware, GUIs): http://kiss.flyduino.net/downloads/
상품의 사용후기를 적어주세요.
게시물이 없습니다
상품에 대해 궁금한 점을 해결해 드립니다.
게시물이 없습니다